1. Superior Screw Holding
Because the core layers of Baltic birch are actually veneers of birch (rather than a softer, secondary wood) and form a void-free core, screws bite and hold with 100% of their threads. Conversely, traditional veneer core plywood has voids and is also made up of softer materials so screws don’t get a chance to clench the best they can.
You also might find sheet goods made with MDF (medium-density fiberboard) core, and though it’s 100% solid, MDF is soft and just doesn’t have the screw-holding power of Baltic birch.
2. Cleaner Joinery
Tipping the hat once again to the uniform birch veneer layers of the core, you’ll get clean dadoes, rabbets, dovetails, miters, and fingers for strong and, when appropriate, great looking joints. Because the core is free of voids, your joinery also won’t suffer from glue starvation—they’ll get 100% glue coverage. Anything you build out of Baltic birch should last a good, long time.
3. Improved Strength and Stability
All plywood runs the risk of warping, and the most common type of warp in plywood is bowing. Baltic birch is not immune, it’s still a wood product. However, Baltic birch has the odds stacked in its favor much better than other plywood, chiefly in 1/2″ and 3/4″ thickness. The cross-banded layers of 1.5 mm thick birch veneer makes the sheets balanced, which promises a flatter product.
However the thinner sheets, like 1/8″ and 1/4″, simply will not remain flat in large pieces—and this is no surprise. That’s usually not a problem though because these are usually used in applications like drawer bottoms and cabinet backs where they’re cut down to smaller sizes or captured in dadoes and rabbets.
It should be obvious that the thicker sheets are more stable because they have more plies. 3/4″ Baltic birch in particular won’t change much in width or length, that’s why it’s great for jigs and fixtures that need to maintain accuracy over the years.
4. Attractive Appearance
One of the fortunate benefits to Baltic birch, too, is that you can leave the edges exposed if you like the look. Because the core is free of voids and all birch, the exposed edges sometimes have an appearance that works for the project, and this saves you time and material—no need to spend time and effort on applying edge tape or solid edge banding unless you want to. Simply sand and finish the edges as they are. The face and back can be stained when you need a different color. Like solid birch lumber, for it to stain evenly with an oil based pigment stain you’ll need to apply a stain controller or a wash coat of de-waxed shellac. Otherwise use dye for even color. To keep the uniform, light color instead, simply finish Baltic birch with a basic clear top coat of lacquer or polyurethane.
5. Thicker Face Veneer with Reasonable Quality
With close inspection of Baltic birch, you should notice that the face and back veneers are remarkably thicker than the veneers you’ll see on traditional cabinet-grade plywood. Sadly, it’s well-known that cabinet grade plywood veneer faces are dismally thin, which makes them easy to damage and easy to sand through. But not so with Baltic birch. Outer veneers are nice and thick. As for the appearance, there are several grades of Baltic birch available, but we most often carry the second highest grade which is BB/BB. BB/BB means both the face and the back veneers are single piece veneers with no splices. Both face and back veneers can have up to 6 small color-matched patches (egg sized footballs or another shape), some light mineral streaks or tight pin knots.
6. Accepts Paper Back Veneer for More Decorative Projects
If you like everything about Baltic birch except its outer birch appearance (or occasional “football” patches), no problem. You can face this plywood with any kind of beautiful wood veneer. Be sure to veneer both sides to maintain its stability.
7. It’s Just the Thing for Laser Cutting and Engraving
It’s one of the few types of wood that can come in large enough sheets and yet be consistently dense through its thickness to be cut with a laser. Anything from parts for architectural models to artwork to schmaltzy engraved knick-knacks.
The downside is that 1/8″ and 1/4″ thick Baltic birch can’t stay perfectly flat. It does cup or warp. It’s not because it’s bad plywood but just an effect of the size. It’s thin and wide. Not a good combo for getting wood to lay flat.
So what do you do? Make a frame or jig that presses it flat and fits your laser cutter. Sometimes all you need is to tape it down to a piece of MDF.
